Bodyboard repair resin – Surf Systeem


Bodyboard repair kit, perfect for all your bodyboard repairs

Sorry, out of stock


Surf System - Bodyresin - Bodyboard and Fins Repair

 BODYRESIN is clear, super flexible, waterproof and resistant.

Product for repair: torn foam, loose rails, folded sliding surface, decks that allow water to pass through and major breaks.

The surface to be repaired should be clean, dry, and all traces of wax should be removed.

Carry out repairs in a ventilated area or outdoors.

Apply and distribute using the spatula. Do not spread with your fingers

BODYRESIN will be dry after 2 hours but it takes 24 hours for the repair to be complete, especially in the case of repairs to deep cracks.

Repair of detached rails
Apply BODYRESIN on the rails and on the board. Wait two minutes and glue the rail.


Repair of the leash anchor point
Apply a large amount of BODYRESIN in the hole. Reposition the plug and seal with the BODYRESIN.


Repair of bent sliding surfaces
Frost the crease and sides to about 6mm. Fill the fold with BODYRESIN and spread it with the spatula.


Repair the holes
The hole must be facing you, fill it with BODYRESIN and leave to act for 24 hours


Repair fins
Apply BODYRESIN to cracked, worn rubber. An application of BODYRESIN bands will strengthen your fins.



Typically surfboards are measured in inches. The length is measured from the nose to the tail. Choosing the length of the surfboard is dependant on your size (weight, height), board type and waves conditions you wish to use the board for.


The widest point of the surfboard is measured from rail to rail. Generally the wider the surfboard the more stable the board, while a board with smaller width maintains better speed and performance.


Surfboard thickness is measured from the top deck to the bottom. The thickness again has a bearing on the board’s performance. Professional surfers will tend to go for the thinner boards as they are lighter and offer better performance.The thicker boards are stronger and because there is more foam under the surfer the boards are more stable.


The bottom curve of a surfboard. Generally the more rocker the surfboard has the more loose (manoeuvrable) the surfboard will be. Where the flatter rocker surfboards will be faster, although they will lack the looseness. The nose is the tip of the surfboard, the nose can vary in shapes and size. Basically the thinner the nose the more response the board will perform, while wider noses are better for stabilization.


Used to increase the strength of a surfboard, a stringer (normally made from wood) runs down the length of a surfboards (typically in the centre of the board from the tip of the nose to the tail).
Boards built with Epoxy, Carbon Fibre and soft boards generally don’t have stringers.


Generally heavier surfers require larger fins to hold the waves better. Although if you prefer to ride a looser (less hold in the waves), smaller fins would be a better option.


Fin configurations have an effect on the ways your surfboards perform.
The following are some of the more common fin configurations.


The single fin was the original fin configuration for surfboards. Based on the idea of the sailboat keel. Single fins are added stabilization and control on the powerful, larger waves, although lack manoeuvrability


Are great for small waves, being fast and manoeuvrable, but when put into tight spots on larger waves, they become hard to control. Popular with Fish surfboards.


Widely recognized as the standard fin configuration, the thruster answers the shortcomings of the single fin and the twin fins configurations.
The thrusters give you stabilization, control and manoeuvrability in all types of surfing conditions.
This concept was the brainchild of Australia’s Simon Anderson


With four fins in the water, Quads boasts an extraordinary amount of holding power in larger surf.
You may think that having four fins would sacrifice speed by creating more drag, but this is not the case.
The both sets of fins are working together on the rail, which makers believe they creates less drag than a board with a centre fin.
The manoeuvrability isn’t sacrificed either, with fins directly under your back foot, the quads are very responsive.


Similar setup to the Twin Fin, although smaller (low profile) fins are generally placed wider (closer to the rails) on the surfboard.
Popular with Fish and Egg / Retro surfboards.

Heeft u hulp nodig bij uw aankoop? Neem dan gerust contact met ons op

+3170 201 5153

Contact formulier