EQ Natural Scented Candle – Costa Rica
The Santa Teresa scented candle takes you away to the deepest tropical rainforest with its authentic, fresh, herbal aroma. Made with plant-based wax. You’ll find an inspiring quote on the reverse side of the beech wood lid.
100% natural, plant-based wax
The Santa Teresa Costa Rica candle unveils fresh notes of bamboo and ocean mist at its heart with a touch of patchouli at its base. Santa Teresa is a small, quiet Costa Rican coastal village which is also considered as one of the country’s best surf spots. Its beaches are packed with sand banks, offering magnificent lefts and long, peeling rights.
- 100% natural, plant-based wax
- Beechwood lid
- Recyclable cardboard and glass
- Wax: European non-GMO Colza oil
- Wick: Lead-free cotton
- Height: 9 cm | Diameter: 7.5 cm
- Made in France
- Burning time : 45 hours
- Hand crafted scented candle
- Weight: 190g
- 100% natural, plant-based wax
Base note : Patchouli
Heart notes : Bamboo, Ocean Mist
Head notes : Water Lily, Jungle Foliage
To enjoy your EQ candle for as long as possible, burn it until the wax surface is completely melted. This will ensure a flat, uniform surface for your next use. Maintain the wick by cutting it regularly to prevent the candle from smoking. Gently re-centre the wick while the wax is still melted after each use to prevent the glass turning black. Avoid placing your candle in breezy areas when burning so as not to let the scent escape. Place it on a suitable base to protect the surface underneath. Once the candle goes out, we recommend you cover it with its beech wood lid to preserve its scent and avoid dust accumulation.
Candle made with European, GMO-free rapeseed oil and lead-free cotton wick.
VEGETABLE OIL, FATTY ALCOHOL, MONO AND DI GLYCERIDES, PERFUME, BENZYL SALICYLATE, TETRAMETHYL ACETYLOCTAHYDRONAPHTALENES, BUTYLPHENYL METHYLPROPIONAL, ACETYLCEDRENE, FORMALDEHYDE CYCLODECYL ETHYL ACETAL, HEXYL SALICYLATE, GERANIOL.
May produce an allergic reaction. Toxic for aquatic organisms. Causes long term adverse effects. Avoid releasing into the environment.
THERE ARE MANY ASPECTS TO SURFBOARD SELECTION THESE ARE THE POINTS TO CONSIDER
Typically surfboards are measured in inches. The length is measured from the nose to the tail. Choosing the length of the surfboard is dependant on your size (weight, height), board type and waves conditions you wish to use the board for.
The widest point of the surfboard is measured from rail to rail. Generally the wider the surfboard the more stable the board, while a board with smaller width maintains better speed and performance.
Surfboard thickness is measured from the top deck to the bottom. The thickness again has a bearing on the board’s performance. Professional surfers will tend to go for the thinner boards as they are lighter and offer better performance.The thicker boards are stronger and because there is more foam under the surfer the boards are more stable.
The bottom curve of a surfboard. Generally the more rocker the surfboard has the more loose (manoeuvrable) the surfboard will be. Where the flatter rocker surfboards will be faster, although they will lack the looseness. The nose is the tip of the surfboard, the nose can vary in shapes and size. Basically the thinner the nose the more response the board will perform, while wider noses are better for stabilization.
Used to increase the strength of a surfboard, a stringer (normally made from wood) runs down the length of a surfboards (typically in the centre of the board from the tip of the nose to the tail).
Boards built with Epoxy, Carbon Fibre and soft boards generally don’t have stringers.
Generally heavier surfers require larger fins to hold the waves better. Although if you prefer to ride a looser (less hold in the waves), smaller fins would be a better option.
Fin configurations have an effect on the ways your surfboards perform.
The following are some of the more common fin configurations.
The single fin was the original fin configuration for surfboards. Based on the idea of the sailboat keel. Single fins are added stabilization and control on the powerful, larger waves, although lack manoeuvrability
Are great for small waves, being fast and manoeuvrable, but when put into tight spots on larger waves, they become hard to control. Popular with Fish surfboards.
THRUSTER 3 FIN
Widely recognized as the standard fin configuration, the thruster answers the shortcomings of the single fin and the twin fins configurations.
The thrusters give you stabilization, control and manoeuvrability in all types of surfing conditions.
This concept was the brainchild of Australia’s Simon Anderson
QUADS 4 FINS
With four fins in the water, Quads boasts an extraordinary amount of holding power in larger surf.
You may think that having four fins would sacrifice speed by creating more drag, but this is not the case.
The both sets of fins are working together on the rail, which makers believe they creates less drag than a board with a centre fin.
The manoeuvrability isn’t sacrificed either, with fins directly under your back foot, the quads are very responsive.
Similar setup to the Twin Fin, although smaller (low profile) fins are generally placed wider (closer to the rails) on the surfboard.
Popular with Fish and Egg / Retro surfboards.
Heeft u hulp nodig bij uw aankoop? Neem dan gerust contact met ons op
+3170 201 5153